Air Button Style Analog Systems and Parts

Tecmark Latching TBS3213 DPDT Air Switch, 25 Amp

Tecmark DPDT (Double Pole Double Throw) air switch used in many older spa controls where a small 5/16" mounting hole is required. Can be mounted in multiple areas, making this switch very versatile. This heavy duty switch is rated at 25 amps and is...

Tecmark TBS-317 Air Switch, DPDT, 20 Amp, Latching - Most Popular Double

This part is a Latching Style Double Pole Double Throw Switch 20 Amp, Hole Through Mount with 1/8" Spout air connector and the Wire connects are male quick connect tabs and required panel hole size is 9/16". This switch is the standard or Universal...

HydroQuip Air Slide Control System Kit, 2 Pumps and Blower, 5.5 KW Heater

HydroQuip Air Series mechanical control system kit with adjustable slide heater. This system supports (1) 2 speed pump (1) single speed pump, (1) air blower, 12 Volt light, ozonator. The adjustable 5.5 KW 15" heater can move up and down the back of the...

HydroQuip Air Slide Control System Kit, 1 Pump and Blower, 5.5 KW Heater

HydroQuip Air Series mechanical control system kit with adjustable slide heater. This system supports (1) 2 speed pump (1) air blower, 12 Volt light, ozonator. The adjustable 5.5 KW 15" heater can move up and down the back of the box or removed and...

Contactor DPST, 40 Amp, 115 Volt Coil

Standard Contactor, double pole single throw (DPST), 40 Amp with 115 volt coil. Most often used for powering the electric heater element, but can be found in other applications. When selecting a new contactor brand names are not really important if your...

Hi-Limit, 1/4" dia, 36"Capillary, SPST, 25A

Single Pole Hi-Limit Switch with 1/4" bulb, 36" capillary and screw terminals for your wiring. The job of this switch is to detect hi-limit conditions at your heater. When it detects a hi-limit error the switch opens and prevents the spa from heating...

Mechanical Thermostat, 5/16" Bulb, 18" Capillary, SPST, 25 Am

Single Pole Single Throw Hi-Limit Switch with screw terminals, rated at 25 amps. The temp bulb has a 5/16" diameter and teh insulated capillary length is 18". This switch will replace models made by Eaton Mears, Robert Shaw and many more. Used to set the...

Hi-Limit, 1/4" dia, 12"Capillary, SPST, Screw Terminal, 25A

Single Pole Hi-Limit Switch with 1/4" bulb, 12" capillary and screw terminals for your wiring. The job of this switch is to detect hi-limit conditions at your heater. When it detects a hi-limit error the switch opens and prevents the spa from heating...

HydroAir Top Draw 1" Air Control Valve Stem, White

This part is a Hydro Air 1" Top Draw Air Control Stem Assembly only, which is made to screw into the air control body. The stem measures about 2 5/8" Across the top and the threaded hole this would screw in would be about 1 3/8" Wide. The shaft from the...

Balboa BP Style Board Repair Kit Set of (2) Relays (3) Jumpers, T-90 Type, Works on Some New Heater Connector Style BP Boards

This kit is a Set of (2) Standard Balboa Board Replacement Repair Relays along with (3) Spade to Spade Jumpers used to do a beef up Jumper Style repair on Some Balboa BP Boards and others...  When replacing board relays you may need this drill bit...

Balboa VS or EL Style Board Repair Kit Set of (1) Relays (2) Jumpers, T-90 Type

This kit is a (1) Standard Balboa Board Replacement Repair Relay along with (1) Spade to Spade Jumper and (1) Spead to Loop Jumper used to do a beef up Jumper Style repair on Some Balboa VS and EL Boards and others...  When replacing board relays...

Barb Adapter, 1/8" Barb x 3/8"mpt, Brass, Jacuzzi Premium, Trombone, Heater

Brass Fitting that fits an 1/8" MPT Jacuzzi heater fitting on one side a 3/8" ID tube on the other side. I have seen these in Jacuzzi Premium Trombone Heaters to attach the heater to the bleeder system though there are many applications this can be used...

Mini Drill Bit Set with Handle Tool for Changing Board Relays

This tool can be used to drill out the hole in the boards when changing out relays.. After you desolder a relay you can use these bits to open the holes up then slide the new relay in the holes and solder.. This also helps you to prevent damage to the...

3 Wire, Thermostat, Invensys, Hydro-Quip, Bulb Size 5/16", 48" Capillary Length , SPDT, 25A, Analog

This part is a 3 Wire Thermostat replacement found in some Air Button Topsides that require 3 wires to operate.. Single pole rated at 25 amps with max temp rating at 107°F. Best results are obtained when the bulb is installed in a dry well or groove...

Bath Control, Electronic, Balboa, On/Off w/Button, 15A, 115V, 20 Min Delay, 99601

This part is a Balboa 115V Control System used in Garden Style Bath Tubs.. You plug the controller into a wall plug, then plug the 115V Bath pump into the controller then mount the button and plug the wire in from the mounted button and the button will...

Indicator Light, 115v, 1/4 Hole Size, Red, Analog System

This Part is a Heater Indicator Light 1/4" mounting hole used to indicate a heater or pump working in a 115V system.. Indicator Light Type    Two-PieceColor    RedVoltage   115vHole Size    1/4"

Set of (2) Relays, Zettler, T-90 Type, SPST, 15vdc, Coil, Balboa Board

This part is for a Set of (2) Standard Balboa Board Replacement Repair Relay made by Zettler. This Relay is the standard relay found on most Balboa Boards but it has double tabs on it so you can add jumpers from the tabs to the feed and load side of the...

Indicator Light, 230v, 1/4 Hole Size, Red, Analog System

This Part is a Heater Indicator Light 1/4" mounting hole used to indicate a heater or pump working in a 230V system.. Indicator Light Type    Two-PieceColor    RedVoltage    230vHole Size    1/4"

Bath Control, Electronic, ACC BC100, On/Off w/Button, 15A, 115V, 20 Min Delay

This part is a 115V Control System used in Garden Style Bath Tubs.. You plug the controller into a wall plug, then plug the 115V Bath pump into the controller then mount the button and plug the wire in from the mounted button and the button will control...

Heater Tube Threaded Plug, 1/8"mpt, Plastic

This item is a 1/8" MPT Plastic Plug which can be used to block an 1/8" MPT (male Pipe Thread) hole normally found on a Heater Tube on Hot Tubs. This hole size is the same size as a Pressure Switch hole and would measure about 3/8" wide across the hole...

PC Board Standoff, 1/4", Reverse Lock, Pack of 12, Balboa and Others Holder Kit

This part is a PC Board Plastic Standoff Holder Kit 1/4" long, Reverse Lock Style, Pack of 12, Fits Balboa and some other Brands...  We also have the 3/4" Version Here: Click for 3/4" Standoff Kit 

NLA PC Board Standoff, 3/4", Reverse Lock, Pack of 12, Balboa and Others Holder Kit

This part is a PC Board Plastic Standoff Holder Kit 3/4" long, Reverse Lock Style, Pack of 12, Fits Balboa and some other Brands...  We also offer the 1/4" version of this part: For the 1/4" Standoff Kit Click Here

How To Video GFCI Breaker Tripping New Wire Up Hot Tub Diagnose The Spa Guy

This video is The Spa Guy teaching you how to Diagnose a New Wire Up Situation where you just wired your hot tub up and it is tripping the breaker and it is either a new tub or it is used and ran fine at the last location...... Save

Hi-Limit, Thermodisc, DPST, Screw Terminal, Surface Mount 230V Hot Tub Spa

This Part is a Thermodisc Style Surface Mount HI LIMIT: Single Pole Single Throw THERMAL FUSE Auto Reset (With NO CAPILLARY)This Hi Limit Surface mount surface mounts to the heater in a spot where it can read what the actual water temperature is flowing...

Hot Tub GFCI Breaker Information How To DIY The Spa Guy

The Spa Guy is talking here about the ins and outs of wiring a GFCI Breaker. Please consult your local codes for actual wiring rules...  #sparepair #hottubrepair  #hottubhowto Save

Voltage in The Water on a Hot Tub How To Video from The Spa Guy

In this video The Spa Guy shows actual voltage in the water on a hot tub and what caused it. a Missing ground on the GFCI box when the hot tub was wired!! Once again The Spa Guy Saves the Day!! Your Hot Tub Super Hero  #sparepair #hottubrepair...

How To Video Hot Tub GFCI Breakers The Basics The Spa Guy Breaker

This video is about The Spa Guy teaching you the basics of GFCI Hot Tub Wiring and the ins and outs of wiring a Hot Tub...  #sparepair #hottubrepair  #hottubhowto Save

Compression Fitting, 1/8" x 3/16" Tube, Brass

Rocker Switch, DPDT, Center Off

Rocker SwitchesHeavy duty 20 amp rating

Air Tubing, 1/8"ID x 1/4"OD, 10ft Roll Used For Air Button, Air Button Style Topside and Switches

This part is a 10' section of Air Tubing 1/8" inside diameter is used with Air Button, Air Button Style Topsides and Air Switch Applications and between Garden Tub Pumps and Air Button Switches...   Air Tubing Inside Diameter 1/8" Tubing...

Barb Adapter, 1/8"b x 1/8"mpt, Brass

Brass Fitting that fits an 1/8" MPT heater fitting on one side a 1/8" ID tube on the other side. I have seen these in AP-1400 Len Gordon Pack to attach the heater to the pressure though there are many applications this can be used for.

Hi-Limit, 5/16" dia, 36"Capillary, SPST, Screw Terminal, 25A

Hi LimitsSingle pole rated at 25 amps with temperature rating set at 121°F. Best results are obtained when the bulb is installed in a dry well or groove tube at or immediately before the heater36" capillary length, 5/16" bulb thicknessThis is a...

Rocker Switch SPST, 16A, 115v, small size

Rocker Switches16 amp rating

Toggle Switch, DPDT, Center Off

Toggle SwitchesHeavy duty 20 amp rating

Timer, Diehl, SPDT, Panel Mount, 115v, 15A, 24hr

Diehl Time Clock Series 800Panel mount, gray face, 24 hour or 7 day, standard 16 amp rating

Timer,Grasslin Repl,SPDT,Panel Mount,115v,w/override,24hr

Grasslin Time ClockPanel mount, moving hands, 24 hour or 7 day, 120 or 240v