Heater Elements

Heater Element, 5.5 KW, Flo-Thru, 115/230V, 7" Titanium

Durable Titanium 5.5 KW heater element with a 7" length. This flo thru element is used with smaller 8-10" heater tubes and can be run at 115 volts for a 1.375 KW heat rating. Please be sure to measure your current element as this is not a very common...

Flo Thru Heater Element - Titanium, 4.5 KW 4500 Watts, 10"

Durable Titanium 4.5 KW (4500 Watt) Heating Element with hardware. Our Titanium Flo-Thru design is a proven performer that provides maximum corrosion protection for even the harshest water environments. With a length of 10" and a terminal spacing of...

Flo Thru Heater Element - Titanium, 5.5 KW 5500 Watts, 10"

Durable Titanium 5.5 KW (5500 Watt) Heating Element with hardware. Our Titanium Flo-Thru design is a proven performer that provides maximum corrosion protection for even the harshest water environments. With a length of 10" and a terminal spacing of...

Hot Springs Replacement Heater Element, 2.5 KW, 230 Volt, NEMA Plug

Hot Springs 230V 2.5KW Flange Mounted Heater Element with three prong NEMA. This generic element has a 2" x 4" mounting plate and was used in many Hot Springs models from 1987-1994. Includes a gasket and o-ring kit to seal the element to the housing...

Hot Springs Replacement Heater Element, 2.5 KW, 230 Volt, Molded J&J Plug

Hot Springs 230V 2.5KW Flange Mounted Heater Element with three prong J&J plug. This generic element is used in Hot Springs Grandee and High Life models from 1987-1994. Easily identified by its 2" x 4" plate. Includes a gasket and o-ring kit to seal...

Hot Springs Replacement Heater Element 1.5 KW, 1500 Watts, 115 Volt, J&J

Replacement Hot Springs flanged heating element, rated at 1.5KW (1500 Watts) at 115 volts operation. This element is for all Hot Springs Spas from 1980-1994 that where 110/115 Volt models. Easily identified by the 4" x 4" heater flange and center...

Hot Tub 2" Heater Union Slice To Plumbing Connect Kit with Glue

This Kit is a 2" Heater Union, Slice Valve, Spin Kit with Glue To Plumbing Connect Kit found in many Hot Tubs. The Heater Union which measures about 3" outside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" coupler to spin it...

Hot Tub 2" Heater Union Slice To Plumbing Connect Kit

This Kit is a 2" Heater Union, Slice Valve, Spin Kit To Plumbing Connect Kit found in many Hot Tubs. The Heater Union which measures about 3" outside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" coupler to spin it to win it...

(1) Jumper Wire, Heater Element, 10 gauge x 4", Relay to Heater, Loop and Spade Connector

This part is a Single of Jumper Wire that would go from a standard heater element Electrode Tab to the board Relay Spade Connector.. Loop for the heater side to female spade.. These can be used on 4.0kw to 5.5kw elements.. Circuit Board...

Set of (2) Jumper Wire, Heater Element, 10 gauge x 4", Relay to Heater, Loop and Spade Connector

This part is a Set of Jumper Wires that would go from a standard heater element Electrode Tab to the board Relay Spade Connector.. Loop for the heater side to female spade.. These can be used on 4.0kw to 5.5kw elements.. Circuit Board...

NLA Jumper Strap, Balboa, Old Style Flat, B2DG, B240, Heater to Board, Qty of 2

No longer available, but we have a better option here: Jumper Wire, Heater Element, 10 gauge x 4", Board to Heater This part is a Jumper Strap Set of (2) Kit to connect the heater to the circuit board on Balboa B2DG and B240 Systems.   Circuit...

Threaded Screwplug Element, 1-1/4" thread, 5.5kW, 230v, 9.75" long

This is a 1-1/4"npt Plug Element that is 9 3/4" long and it threads into a fitting in the plumbing.. With 10-32 thd studs, dual 5/16" thermowells, predrilled holes for mounting junction box 1-1/4" threaded elements measure 1-1/2" outside diameter.....

Jumper Wire, Heater Element, 10 gauge x 4", Board to Heater

This part is a Set of 4" Jumper Wires that would go from a standard heater element Electrode Tab to the board bolts.. These can be used on 4.0kw to 5.5kw elements to transfer voltage from the circuit board to your heater. Uses a 10 gauge wire...

How To Video GFCI Breaker Tripping New Wire Up Hot Tub Diagnose The Spa Guy

This video is The Spa Guy teaching you how to Diagnose a New Wire Up Situation where you just wired your hot tub up and it is tripping the breaker and it is either a new tub or it is used and ran fine at the last location...... Save

Video How To Hydro-Quip Hot Tub Breaker Trip Heater The Spa Guy

This video is about The Spa Guy diagnosing a Breaker Tripping on a Hot Tub With Hydro-Quip Controls... How To Replace the Heater Element and final diagnostic verification of operation.... Save

Heater Element 4.0kw Kit Hot Tub Spa Part M7 Balboa Gecko Hydroquip Titanium (Best)

This part is a 4.0KW Titanium (Best) Heater Element, 10".  Our durable titanium Heater Element features the bend in the back of the element needed to fit the Balboa M-7 heater tubes and has the standard 1-1/4" spacing between the element...

Hot Tub GFCI Breaker Information How To DIY The Spa Guy

The Spa Guy is talking here about the ins and outs of wiring a GFCI Breaker. Please consult your local codes for actual wiring rules...  #sparepair #hottubrepair  #hottubhowto Save

How To Video for Heater Element Nut Spins or Stuck Flow Through Repair Spa Guy

This video is about The Spa Guy showing How To Remove a Heater Element where the nuts are spinning in the tube and will not turn off...... it is a similar process on all brands... Save

Voltage in The Water on a Hot Tub How To Video from The Spa Guy

In this video The Spa Guy shows actual voltage in the water on a hot tub and what caused it. a Missing ground on the GFCI box when the hot tub was wired!! Once again The Spa Guy Saves the Day!! Your Hot Tub Super Hero  #sparepair #hottubrepair...

Heater Element 5.5kw Gasket Kit Hot Tub Spa Part M7 Balboa Gecko Hydroquip Titanium Silicon Kit (Best Value)

This Part is a 5.5KW Titanium Heater Element with (2) Heater Union Gaskets and a 1/2Oz Tube of Special Hot Tub Formulated Silicon Sealer to Seal the Threads. This Heater Element features the bend in the back of the element needed to fit the Balboa M-7...

Heater Element 4.0kw Gasket Kit Hot Tub Spa Part M7 Balboa Gecko Hydroquip Titanium Silicon Kit (Best Value)

This part is a 4.0KW Titanium Heater Element with (2) Gaskets and a 1/2Oz Tube of Special Hot Tub Formulated Silicon Sealer to Seal the Threads. This Heater Element features the bend in the back of the element needed to fit the Balboa M-7 heater...

How To Video Hot Tub GFCI Breakers The Basics The Spa Guy Breaker

This video is about The Spa Guy teaching you the basics of GFCI Hot Tub Wiring and the ins and outs of wiring a Hot Tub...  #sparepair #hottubrepair  #hottubhowto Save

Flange Element, 3" x 3", 11.0kW, Raypak, 230v, w/Gasket

Raypak Replacement Element3 x 3 flange, 4 mounting holes, flying wire leads, welded construction

Screwplug Element, 1"thd, 5.5kW, C-Spa XI, 15-1/4", 230v

1" Screw Plug, Screw on TerminalsNo thermowells, 5.5kW/240v ratingCalSpa, Ramco1" thd elements measure 1-1/4" o.d

Flow Thru Element, 3.0kW, Incoloy, 10", 115v or 230v

This part is a Standard 3.0KW Heater Element 115v or 230V that features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, and most other standard Hot Tub Heater Tubes.   This part...

NLA Jumper Strap, Balboa, Value, LE, Heater to Board, Qty of 2

No longer available, but we have a better option here: Jumper Wire, Heater Element, 10 gauge x 4", Board to Heater This part is a Jumper Strap Set of (2) Kit to connect the heater to the circuit board on Balboa LE and Value Systems. Measures 1-3/8" x...

Center Mount, Flow Thru Element, 5.5kW, 115v or 230v, 10", Middle Terminal

This part is a Center Mount 5.5KW Incoloy Heater Element for 230V or 115V Applications. Center mount means the holes for the electrodes are in the center of the tube to to one side or the other.. This is a very rare style but they are out there....

Heater Element, 5", Flange, 5.5kw, Brett Aqualine, Gasket,O-Ring, Vita

This part is a 5"x 5" Flange Element 5.5kw at 230V or 1.375Kw at 115V with a Gasket, O-Ring and Bolts. This flanged element is found in Plastic Heater housings in Brett Aqualine, Premier  Allstate and Hot Water Products. I have also seen this...

(F) Flow Thru Element, 4.0kW, M7, Generic, 115v/230v, Teflon Coated (Better)

You are buying a 4.0KW Chemical Resistant DuPont Teflon® Coated Flow Thru Heater Element for 230V or 115V Applications that features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, and most...

Screwplug Element,1"thd,1.5/5.5kW,Comfortzn/Coates,115v/230v

NLA Jumper Strap, Balboa, EL, VS, GL, GS, Heater to Board, Copper

No longer available, but we have a better option here: Jumper Wire, Heater Element, 10 gauge x 4", Board to Heater This Part is a Single Jumper Strap for a Balboa, EL, VS, GL or GS, Heater to Board connection.. This part is made from Copper.. Measures 2"...

(B) Flow Thru Element, 5.5kW, M7 , 10-1/2", 115/230v, Teflon Coated ( Better)

You are buying a 5.5KW DuPont Teflon® Coated Flow Thru Heater Element for 230V or 115V Applications that features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, and most other standard...

Heater Element 5.5kw Hot Tub Spa Part M-7 Universal 230V or 115V Incoloy (Good)

This part is a Standard 5.5KW Incoloy Heater Element for 230V or 115V Applications that features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, and most other standard Hot Tub Heater Tubes...

Heater Element 4.0kW Universal 10" 115v/230v M7 Bend Incoloy (Good)

This part is a Standard 4.0KW Heater element that features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, and most other standard Hot Tub Heater Tubes.   This part used in newer...